FSC 3010 Torque Converters and Speed Changers

Includes Fluid Couplings; Nonvehicular Clutches and Couplings; Horizontal Right Angle Drive Gear Units. Excludes Automotive Torque Converters (FSC 2520); Vehicular Power Transmission Components (FSC 2520); Rotary Aircraft Transmission Gear Units (FSC 1615).

Name NSN Details  
Carrier,gear Assembly 3010-01-502-9464 A device designed to support and position one or several gear assemblies functioning as a unit. It may contain bearings, shafts, pins or the like. RFQ
Housing,mechanical Actuator 3010-01-503-0676 An item with different cross sections. It is designed to accommodate and support the power transmitting mechanism of an ACTUATOR, MECHANICAL, MANUAL or an ACTUATOR, MECHANICAL, LINEAR. RFQ
Housing,mechanical Actuator 3010-01-503-0689 An item with different cross sections. It is designed to accommodate and support the power transmitting mechanism of an ACTUATOR, MECHANICAL, MANUAL or an ACTUATOR, MECHANICAL, LINEAR. RFQ
Clutch Assembly,friction 3010-01-503-1031 A spring loaded device designed to connect and disconnect power between a driving device (engine, motor, and the like) and a driven member (transmission and the like). It may be of wet or dry design. Includes cover, and may include intermediate plates, and/or DISK, CLUTCH. RFQ
Drive Unit,angle 3010-01-503-1050 An assembly of gears, shaft and bearings within a housing, specifically designed to change the direction of rotary motion by an angle of more than zero degrees and less than one hundred eighty degrees. It may or may not have a torque differential from input to output. Excludes GEAR ASSEMBLY, SPEED DECREASER and GEAR ASSEMBLY, SPEED INCREASER. RFQ
Coupling,shaft,rigid 3010-01-503-1114 A device for connecting the ends of two shafts to produce in effect, one piece of rigid shafting so that the rotary motion of one shaft is transmitted to the other shaft. Couplings of the sleeve type must have an over-all length exceeding the outside diameter, or must have an internal spline. RFQ
Coupling,shaft,flexible 3010-01-503-1115 A device for connecting the ends of two shafts so that rotary motion of one shaft is transmitted to the other shaft. It is constructed to allow for slight misalignment of shafts both linear and angular. RFQ
Gear Assembly,speed Decreaser 3010-01-503-1133 A group of gear(s) and/or worm(s), of fixed ratio, specifically designed for the purpose of decreasing the speed from the driver(s) to the driven shaft or shafts; having no reversing feature except by reversing the prime mover. See also TRANSMISSION (as modified) and GEARCASE-MOTOR. RFQ
Hub,clutch 3010-00-001-6187 RFQ
Coupling Half,shaft 3010-00-001-6242 A mechanical item used to connect a shaft and the mating member of a flexible or rigid coupling. RFQ
Housing Sensor Asse 3010-01-503-1473 RFQ
Housing Sensor Asse 3010-01-503-1490 RFQ
Coupling,shaft,rigid 3010-01-503-1548 A device for connecting the ends of two shafts to produce in effect, one piece of rigid shafting so that the rotary motion of one shaft is transmitted to the other shaft. Couplings of the sleeve type must have an over-all length exceeding the outside diameter, or must have an internal spline. RFQ
Universal Joint,nonvehicular 3010-01-503-1567 A flexible connection designed for nonvehicular applications which permits rotary motion to be transmitted between two shafts located at an angle to each other. The angle between the shafts may be continually varied within certain limits; the connecting ends must have either a flange, hub, or splined stub shaft; the plain portion of a splined stub shaft must not exceed the length of the splines. Excludes drive or propeller shafts with joint(s) at one or both ends. See UNIVERSAL JOINT,GEARED. RFQ
Spider,universal Joint,non Vehicular 3010-01-503-1689 RFQ
Spider,universal Joint,non Vehicular 3010-01-503-1717 RFQ
Spider,universal Joint,non Vehicular 3010-01-503-1722 RFQ
Coupling,shaft,rigid 3010-01-503-1872 A device for connecting the ends of two shafts to produce in effect, one piece of rigid shafting so that the rotary motion of one shaft is transmitted to the other shaft. Couplings of the sleeve type must have an over-all length exceeding the outside diameter, or must have an internal spline. RFQ
Universal Joint,nonvehicular 3010-01-503-2055 A flexible connection designed for nonvehicular applications which permits rotary motion to be transmitted between two shafts located at an angle to each other. The angle between the shafts may be continually varied within certain limits; the connecting ends must have either a flange, hub, or splined stub shaft; the plain portion of a splined stub shaft must not exceed the length of the splines. Excludes drive or propeller shafts with joint(s) at one or both ends. See UNIVERSAL JOINT,GEARED. RFQ
Gear Box Assy 3010-01-503-2081 RFQ